Cement & Concrete Testing Instruments

Product Details:

Compacting factor apparatus conforming to IS 1199, 5515. & BS 1881-103      Rs. 11500/-
The apparatus is used for determining the workability of fresh concrete, provided the maximum size of the aggregate does not exceed 38mm. The test is particularly useful for concrete mixes of very low workability where true slump values are not reliable.
Specification : It consists of two rigid conical hoppers and a cylinder mounted on a rigid metal frame. The lower openings of the hoppers are fitted with hinged trapdoors having a quick release catches. A circular metal plate is provided to cover the top of the cylinder. Supplied complete with one plaster's trowel and one tamping rod, 16mm dia x 600mm long, both ends rounded.

Additional Information:

• Packaging Details: Wooden Packing

Product Details:

Proving Rings _ Compression Type:
They are made out of special steel carefully forged to give maximum strength and machined to give highest sensitivity combined with stability to ensure long life and accuracy. When Compressive or tensile load is applied within the elastic range, the proving rings get temporarily deformed. This deformation is measured by a sensitive dial gauge fixed co-axially at the center of proving ring. The dial gauge readings thus obtained versus load applied enable the operator to find out unknown load, just by noting the dial gauge reading for unknown load. The proving rings have high elasticity and on removing load they regain their original shape provided they are loaded in their elastic limits.

Salient Features

A Dial gauge and plunger anvil is mounted on brackets clamped to the ring body. The dial gauge is held perfectly rigid without the remote chance of shifting due to inadvertent shocks or pressures exerted on it. The dial gauge plunger rests on an adjustable anvil. Proving Rings, from 50 kgf to     1,00,000 kgf capacity provided with 1/2 inch B.S.F female threads. Loading bosses and a loading ball nipple and steel ball are supplied with each ring. Rings of capacity over 25000kgf (or 25 tonnes / 250 kn) are not thus threaded. Each ring is individually calibrated and supplied with works calibration chart and a carrying case.

Calibration charts from Standard Laboratories for the Proving Rings ordered are also available at extra cost.
All Proving Rings are Integral Type.
a. cap.above 50 to 500 kgf.       Rs. 4400/-
b. cap.above 500 to 3000 kgf.   Rs.6600/-
c. cap above.3000 to 5000 kgf.  Rs. 8700/- 
d. cap above.5000 to 10000 kgf. Rs. 10400/-
e. cap above.10000 to 20000 kgf. Rs. 12400/-
f. cap above.20000 to 30000 kgf.  Rs. 13600/-
g. cap above.30000 to 50000 kgf.  Rs.16000/-
h.cap above 50000 to 100000 kgf.  Rs.21000/-
i. cap above 100000 to 200000 kgf. Rs.29600/-
j. cap above 200000 to 300000 kgf  Rs.52000/-

Additional Information:

• Production Capacity: Depends on order
• Delivery Time: 5-7 days
• Packaging Details: Card Board/ Wooden packing

Product Details:

Sieve Shaker - Rotap

Designed to carry up to 7 sieves of 8” dia it is driven by ¼ HP electric Motor, through reduction gear. The whole gear mechanism, which gives circular end to end motion runs in an oil bath. The Tapping motion given By hammer from to. To work on 220/230 V single Phase AC. Supplied Complete with adaptor for  8” sieve but without test sieve.

(i)With “PERFECT” motor      Rs. 60000/- each

(ii) With “CROMPTON” motor  Rs. 72000/- each

(iii) With 0-60 min. Automatic timer “IMPORTED” extra for above. 
Rs. 2250/-  each

Product Details:

Volume change apparatus, used for determination of volume change of cement concrete. Consists of a mould 75mm X 75mm X 250mm effective gauge between inner most point, complete with length comparator equipped with dial gauge least count 0.002mm x 5 mm    Rs12800/-

Product Details:

Standard test sieves as above but made out of 45cm diam G.I.Frame

Aperture size

125mm,   Rs 450/-

100mm,   Rs 450/-

90mm,      Rs 450/-

80mm,      Rs 450/-

75mm,      Rs 450/-

63mm,       Rs 450/-

53mm,       Rs 450/-

50mm,       Rs 450/-

45mm,       Rs 450/-

40mm,       Rs 450/-

37.5mm,    Rs 450/-

31.5mm,     Rs 450/-

26.5mm,     Rs 450/-

25mm,     Rs 450/-

22.4mm,   Rs 450/-

20mm,     Rs 450/- 

19.0mm,   Rs 450/-

16,0mm,   Rs 450/-

14mm,      Rs 450/-

12.5mm,   Rs 450/-

10mm,       Rs 450/-

9.5mm,      Rs 450/-

8mm,         Rs 450/-

6.3mm,      Rs 450/-

4.75mm      Rs 450/-

lid and pan.     Rs 450/-
Standard Test Sieves AS above but dia300 mm 350/- each

Product Details:

Bulk density test apparatus as per I.S. 2386 Part IV. Determines bulk density or unit weight of aggregates.   
Rs 4500/-

Specifications: Calibrated cylindrical measures of sheet iron with handles. Consists of 3 measures one each 3 litres capacity, 15 litres capacity and 30 litres capacity. Complete with one tamping rod, round, 16mm dia and 600mm long, one end rounded.

Spares

Measure of 3 Litres     Rs.900/-

Measure of 15 Litres   Rs. 1600/-

Measure of 30 Litres   Rs.2500/-

Tamping Rod round, 16mm dia and 600mm long   Rs.200/-

Product Details:

Cube Mould –Gang Of Three:  as per IS : 10080/10086. Three-gang, 2" cube mold with diagonal arrangement in cast iron. Reinforcing rib prevents spreading with detachable single base plate. Rs.3300/-

Product Details:

Compression Testing Machine Hand cum Electrically Operated 4 Pillar Welded type

250 KN Single Gauge   Rs. 39000/-

500 KN Single Gauge   Rs. 41000/- 

1000 KN Single Gauge Rs. 51000/-  

1000 KN Triple Gauge  Rs. 60000/-

1500 KN Single Gauge Rs.65000/- 

2000 KN Single gauge Rs.73000/-                                                                                                       
2000 KN Triple Gauge      Rs.83000/-

Additional Information:

• Production Capacity: Depends on order
• Delivery Time: Within 7 Days
• Packaging Details: Wooden Packing

Product Details:

Vee Bee Consistometer  IS 1199 & BS EN 12350.
The instrument is used for workability as well as consistency of fresh concrete. A slump Cone and a graduated rod supplied with the instrument helps the operator to find out slump values and vibration table with container and acrylic disc is used to find out workability of concrete expressed in Vee Bee degrees, which is defined as the time in seconds to complete required vibrating at which the fresh concrete flows out sufficiently to come in contract of the entire face of acrylic disc.
The equipment consists of : A vibrating table size 380mm long and 260mm wide, resting upon elastic support at a height of about 305mm above the floor, complete with Start/Stop switch, cord and plug. A holder is fixed to the base in to which a swivel arm is telescoped with funnel and guide swivel arm is also detachable from the vibrating table. The divisions of scale on the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16mm dia and 600mm long rounded at both ends.   

Additional Information:

• Production Capacity: Depends on order
• Delivery Time: 3-5 days
• Packaging Details: Carton or wooden case

Product Details:

Aggregate crushing value apparatus AS per IS 2386 partIV used for measuring resistant of an aggregate and determine 10 percent value consists of a open cylinder 150 mm diam base plate plunger and tamping rod Rs. 3800/-

Product Details:

10 kN capacity proving ring to measure the applied load.  Rs.8700/-

Additional Information:

• Production Capacity: Depends on order
• Delivery Time: 6-8 days
• Packaging Details: Wooden case

Product Details:

Curing Tank 

 

Curing Tank Inner SS outer MS up to 100*C  10”x25”x15” for 3 moulds     Rs. 31000/-

Curing Tank Inner SS outer MS up to 100*C  16”x25”x15” for 6 moulds     Rs. 36000/-

Curing Tank Inner SS outer MS up to 100*C  32”x25”x15” for 12 moulds Rs. 48000/-

Curing Tank Inner SS outer MS up to 100*C  50”x33”x15” for 24 moulds Rs. 70500/-
 

Additional Information:

• Production Capacity: 3-24 moulds
• Delivery Time: 5-7 days

Product Details:

Capping Set (Vertical)IS : 516 1959, BS 1881-120 For cylinders 150mm dia x 300mm long Rs. 6500/-
For capping compression cylinder specimens. This apparatus can be used both in the laboratory and in the field. The specimens capped in this apparatus have plane parallel faces.
Specification Consists of a base with an upright. The upright serves as a guide for positioning the capping plate and cylinder. The capping plate is machined accurately. There is a recess in the plate for keeping the molten capping compound and to position cylinder. Complete with cylinder carrier and ladle

50mm Rs. 2400/-

75mm Rs. 3500/-

100mm Rs. 5400/-

Product Details:

Capping Set (Horizontal) IS: 516 1959, BS 1881-120, ASTM C31, C 617,
For 15cm dia x 30cm length cylinders Rs. 9800/-
SpecificationThe set comprises of a cylinder capper, a cylinder carrier and a ladle. The cylinder capper consists of a base on which two accurately machined plates are mounted vertically. One plate is firmly fixed and the other one is adjustable horizontally. Two plates are provided with holders for holding the cylinder in position. The holder are split and the bottom half of each holder is fixed firmly and the top half of each is removable and bolted down to the lower half. On the upper parts of the vertical plates ''V'' s are provided for pouring the capping compound. Two spacers are also provided. Complete with cylinder carrier and ladle for molten compound .

50mm Rs. 4500/-

75mm Rs. 6500/-

100mm Rs. 8600/-

Product Details:

• Flexural Testing Machine. IS : 516 BS 1881, ASTM C78  Hand operated Rs.28400/-
  The machine consists of a hand frame. The lower platen has two rollers the distance between which is adjustable For 150 mm x 150 mm x 700 mm beam, the centre distance between rollers is 600 mm, while it is 400 mm for beams of size 100mm x 100mm x500mm. The upper platen has also a pair of rollers whose distance is adjustable. It is 200mm centre to centre, for 150mm x 150mm x 700mm size beam and 133 mm for 100 mm x 100 mm x 500 mm size beam. A pressure gauge to indicate load is fixed on the load frame. A small pumping unit is attached to the load frame. Total capacity of the machine is 100 KN and a 150mm dia pressure gauge 0-100 KN x 1 KN is fitted on the machine Since this is a hand operated light weight machine, its is useful for field laboratory also.

  As above but electrically operated, operation on 220 Volts,  Rs 48000/-

Additional Information:

• Production Capacity: Depends on order
• Delivery Time: 8-10 days
• Packaging Details: Wooden Packing

Product Details:

Riffle sampler divider,  We are offering a wide range of Riffle Sample Divider. Riffle sample dividers are used for the easy dividing and reduction of bulk material samples with particle sizes ranging from less than 1 mm up to a maximum of 10 mm. Our Riffle sample divider consists of a sheet metal box mounted on legs and fitted with a series of chutes or equal width which discharge the material alliteratively in opposite directions into speculate panes. This equipment is mainly used for sampling aggregates, cement, ores, refractory materials, pigments, soap, powdered coal etc. It is also used for rapid collection of true representative sample from aggregates.

Slot width 12.5/13mm nos of slot 14 Rs. 6500/- each 

Slot width 15mm nos of slot 14      Rs. 7500/- each

Slot width 20mm nos of slot 14     Rs. 8500/- each 

Slot width 25mm nos of slot 14     Rs. 9500/- each 

Slot width 50mm nos of slot  8                 Rs. 11000/-  Each

Product Details:

Vibrating Hammer – DLC Hammer Vibration compaction set used to compact soil samples for use in tests referencing ASTM D7382-08 methods. This method refers to the determination of the maximum dry unit weight and water content range for the effective compaction of granular soils using a vibrating hammer. The test set includes a heavy-duty frame designed specifically for easily mounting a vibration hammer 

Product Details:

Permeability - Cement Mortar and Concrete Permeability Equipments. These are manufactured in adherence to industrial quality standards. These equipments are known to assess the permeability of cement mortar and concrete. Various parts of the equipment are made using premium materials such as Brass. These sturdy and robust equipments can easily withstand strong impacts as well as corrosion. These are known for their accurate permeability measurement and reliability.
Specifications :
Parts of the device are made out of premium materials like brass

High reliable in determining permeability of materials

Device is sturdy and can stand corrosion

Permeability – Cement, Mortar & Concrete  100 mm Single Cell  MS    Rs.29600/-

Permeability – Cement, Mortar & Concrete  100 mm Single Gunmetal            Rs.41800/- 

Permeability – Cement, Mortar & Concrete  150 mm Single Cell  MS    Rs.38600/-

Permeability – Cement, Mortar & Concrete  150 mm Single Cell  Gunmetal       Rs.52800/-

Permeability – Cement, Mortar & Concrete  150 mm Three Cell  MS     Rs.104800/-

Permeability – Cement, Mortar & Concrete  150 mm Three Cell  Gunmetal   Rs.143200/-

 

 

Additional Information:

• Production Capacity: Depends on order
• Delivery Time: 6-8 days

Product Details:

Hand Operated Compression Testing Machines conforming to specifications and tolerance in accordance to I.S. 516 for determination compressive strength on cube moulds and other objects, manually operated with hardened platens and pressure gauge calibrated against NCCBM.Tested proving ring or master gauge

Product Details:

 

Flow Table Apparatus  (As per IS 9103: 1999) The flow table apparatus shall be constructed in accordance with Fig. 1A and 1B. Flow table top shall be constructed from a flat metal plate of minimum thickness 1.5 mm. The top shall have a plan area of 700 mm × 700 mm and a flatness of within 1.5 mm. The centre of the table shall be scribed with a cross, the lines of which run parallel to and out to the edges of the plate, and with a central circle 200 mm in diameter. The under surface of the plate shall be reinforced in order to prevent distortion of the flat surface. The front of the flow table top shall be provided with a lifting handle. The total mass of the flow table top shall be 16 ± 1 kg.

The flow table top shall be hinged to a base frame using externally mounted hinges in such a way that no aggregate can become trapped easily between the hinges or hinged surfaces. The front of the base frame shall extend a minimum 120 mm beyond the flow table top in order to provide a top board. An upper stop similar to that shown in Fig. 1A shall be provided on each side of the table so that the lower front edge of the table can only be lifted 40 ± 1 mm.The lower front edge of the flow table top shall be provided with two hard rigid stops which transfer the load to the base frame. The base frame shall be so constructed that this load is then transferred directly to the surface on which the flow table is placed so that there is minimal tendance for the flow table top to bounce when allowed to fall.

C-1.4.1 Mould

The mould is made of a metal readily not attacked by cement paste or liable to rust and of minimum thickness 1.5 mm. The interior of the mould shall be smooth and free from projections, such as protruding rivets, and shall be free from dents. The mould shall be in the form of a hollow frustrum of a cone having the internal dimensions as shown in Fig. 2. The base and the top shall be open and parallel to each other and at right angles to the axis of the cone. The mould shall be provided with two metal foot pieces at the bottom and two handles above them.

C-1.4.2 Tamping Bar

The tamping bar shall be made of a suitable hardwood and having dimensions as shown in Fig.

 

Product Details:

Aggregate impact tester. Conforming to specifications and tolerance in accordance’s to I.S. 2386 Part IV. Sturdy construction consists of a base support columns to form a rigid frame work around the quick release mechanism to ensure effective fall of the hammer during test, the free fall can be adjusted 380mm. The hammer is provided with locking arrangement.Supplied complete with one cylindrical cup and metal measure 75mm dia x 50mm with tamping rod 7000/-

Additional Information:

• Delivery Time: 1-2 days
• Packaging Details: Bora packing

Product Details:

Vibrating table, The Vibrating Table is used for compacting concrete cubes and cylinders.

Specifications: It is designed to carry a load of 140 kg. The apparatus consists of a motor fitted with a variable pitch pulley housed in a cabinet. The vibrations are imparted by means of off-balance masses rotating on a shaft of a vibrator clamped to the underside of the table top. The table top is 50cm x 50cm. and has stops along its edges to prevent moulds from walking off the table during vibration. A cross arm adjustable on a vertical rod at the center of the table is provided to hold the moulds while operating the table. The variable pitch pulley arrangement permits the frequency to be varied between a maximum of 3600 vibrations per minute. A speed regulation handle is provided for increasing or decreasing the frequency. A switch is provided for starting the motor, suitable for operation on 440 volts, 3 phase, 50 cycles, A.C.supply.  Rs. 14500/-

Vibrating table as above but table top is 60cm x 60cm Rs. 16000/-

 

Vibrating Tables as above but table top size 75cm x 75cm Rs. 29000/-

Vibrating Tables as above but table top 100cm x 100cm . Rs. 35000/-

 

Additional Information:

• Production Capacity: Deprnds on order

Product Details:

Vibrating machine, conforming to IS 4031 The vibrating machines which we offer are also called mould vibrator or mortar cube vibrators. Our vibration machines are used for the preparation of mortar cubes for the determination of compression strength of ordinary and rapid hardening:

·         Portland cement

·         Low heat Portland cement

·         Portland blast furnace cement

·         High alumina cements

Salient Features

·         The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base.

·         The complete frame assembly consists of a vice to hold a 7.06 cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould.

·         This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame.

·         A balance weight is an integral bottom part of the frame.

·         The centre of gravity of the assembly is brought to the centre of the eccentric shaft or within a distance of 25mm mould.

·         The frequency of vibration is 12000 400 vibration per minute.

·         Supplied complete with on 7.06cm cube mould with loose base plate, a time switch 0-5mins x 1min and certificate of vibration from a standard laboratory.

·         Spares offered: Set of springs, belt and belt guard

 

As above but with digital timer     Rs.17500/-

Additional Information:

• Production Capacity: Depends on order
• Delivery Time: 1 Week
• Packaging Details: Wooden Packing

Product Details:

Flow Table conforming to specifications and tolerance in accordance to IS 5512  Consists of brass top of 250mm dia . complete with Brass Mould  Hand operated  Rs. 9500/- each

^{Llow Table As per IS 5512  As above But Electrically opeated 
Rs. 16500/- each}

Product Details:

Cube Moulds  These are available in different sizes and are made according to Indian and British standards. For the metric size cube moulds, the faces are machined flat to 0.02mm accuracy and finished to within 0.02mm. For the inch size moulds, the faces are machined flat to 0.01 inches and finished to within 0.01 in. All moulds are supplied complete with base plate.

Cube mould 15cm x15cm x15cm +7 kg Cast Iron  Rs. 790/-

Cube mould 15cm x15cm x15cm +8 kg Cast Iron  Rs.870/-

Cube mould 15cm x15cm x15cm +9 kg Cast Iron  Rs.1280/-
Cube mould 15cm x15cm x15cm CastIron ISI MarkRs. 2250/-

Cube mould 15cm x15cm x15cm Plastic Commercial Rs.520/-

 

Cube mould 15cm x15cm x15cm Plastic Superior  Rs.940/-

Cube mould 10cm x10cm x10cm Cast Iron            Rs.630/-

Cube mould 7.06cm x7.06cm x 7.06cm Cast Iron  Rs. 450/-
Cube mould 7.06cm x7.06cm x 7.06cm ISI mark  Rs.1240/-

Cube mould 5cm x 5cm x 5cm Cast Iron               Rs.410/-

Cube mould 10cm x10cm x10cm MS                     Rs.1270/-

Cube mould 7.06cm x7.06cm x 7.06cm MS           Rs.450/-

Cube mould 5cm x 5cm x 5cm Cast MS                Rs.  410/-                              

Additional Information:

• Production Capacity: Depends on order
• Delivery Time: Depends on order
• Packaging Details: Open

Product Details:

Flexural Testing Machine 400 Kg (4 KN) Conforming to specifications and tolerance in accordance IS 4031 We are delivering a wide range Flexure Testing Machine (4 Kn) to our esteemed consumers. The speed is adjusted, so that the load increase on the specimen is between 4 to 6 Kg / sec. A flexure test attachment for keeping the specimen in position is also supplied. This consists of two rollers of 10 mm Diameter and spaced 100 mm apart and a third roller of the same diameter equidistant from the first two and for transmitting the applied load to the opposite face of the prism. The unit is for operation on 230 volts, single phase, 50 cycles A.C. supply. These are attainable at most affordable market rates    Rs.29000/-

Product Details:

Beam Mould Made of Cast Iron BS 1881-108 For casting, concrete specimen for flexure tests
Specification: Made of Cast Iron / Mild Steel. The moulds are made of 4 plates assembled together. Each mould is supplied complete with base plate. Faces are machined flat to ± 0.2mm. And finished in

10 cms x10 cms x 50 cms   Rs. 2300/-

15 cms x15 cms x 70 cms   Rs. 3500/-

15 cms x15 cms x 75 cms   Rs. 4200/-

Beam Mould Made of Mild Steel

10 cms x10 cms x 50 cms   Rs. 2500/-

15 cms x15 cms x 70 cms   Rs. 3600/- 

15 cms x15 cms x 75 cms            Rs.  4350/-

Product Details:

Pan Mixer concrete Pan Mixer is useful device for weighing for production of controlled concrete, mounted on robustly fabricated chassis of heavy steel section with M.S. Body Lever mechanism is suitably designed with bearing for proper weighing. Discharge chutes designed for quick discharge of aggregate in the mixer hopper.

Capacity

40 ltr     Rs. 75000/-

56 ltr         Rs. 95000/-

Additional Information:

• Delivery Time: 2 weeks
• Packaging Details: Wooden Packing

Product Details:

Density Basket -For density tests on aggregates as per procedure lay down.

Salient Features

Specifications: Made of brass with stainless steel wire mesh 6.3mm size ruggedly constructed, approximately 20cm dia x 20cm high. Complete with handle  Rs.600/-

Product Details:

Buoyancy Balance We provide buoyancy balance which helps widely in determining the specific gravity and for the water absorption of the aggregate. Our unit is fitted with the 15 kg capacity x 0.5 gm of the electronic balance. The frame is supplied with:

• Water tank.

• Suspension hooks.

• Lever for lifting the water tank manually.

Moreover, it can be easily customized in accordance with client requirement and can be delivered within stipulated time frame

The density of hardened concrete specimens such as cubes and cylinders can be quickly and accurately determined using a Specific Gravity / Buoyancy Balance. The apparatus consists of a rigid support frame, incorporating a water tank mounted on a platform. A mechanical lifting device is used to raise the water tank through the frame height immersing the specimen suspended below the balance. The Balance is not included in the apparatus and must be ordered separately. Any type of Electronic Balance fitted with an under bench weighing facility can be used. The balance supplied can also be used as a standard weighing device, thus providing a versatile and comprehensive weighing system in the laboratory Rs. 22500/-

Product Details:

Cylindrical Mould Made of Cast Iron For testing concrete cylinders for compressive strength tests.
Specification: The mould is split vertically into two parts. The mean internal diameter in within +0.2mm and height is within +1mm. The ends are machined to +0.05. The base plate and top plate are machined flat to +0.03mm.

5 cms diam X 10cms height Rs. 850/-

7.5 cms diam X 15 cms height Rs. 1300/-

10 cms diam X 20cms height Rs.1550/-

15 cms diam X 15cms height Rs. 1400/-

15 cms diam X 16cms height Rs. 1650/-

15 cms diam X 30cms height Rs.2600/-

Product Details:

L Box - Method used to determine flow rates and passability of Self-consolidating concrete in confined spaces, as well as an evaluation of filling, passing ability and segregation resistance. Applicable to concrete with aggregates of 1" (25mm) maximum size. Test box is comprised of concrete reservoir, a slide gate, an obstacle grid comprised of 3 bars and a test basin. Includes metal strike-off bar and instructions.  Rs 9800/-

Product Details:

Pocket Penetrometer Concrete is lightweight for field and lab evaluation of the initial set of concrete mortar based on ASTM C-403. Penetration plunger has a 1/20 sq. inch tip area. Calibrated range for the pocket penetrometer is 0-700 psi. 

Product Details:

Sand Cone with Tamper As per ASTM: C 128, AASHO: T 84
Used for determining the slumps of fine aggregate in the determination of bulk and apparent specific gravity and absorptionof fine aggregate. The Equipments comprises of a conical metal mould 1.5inch dai. at the top, 3.5 inch dia. at the base and 2.7/8 inchin height. A metal tamping rod weighing 12 ounces and having a flat circular tamping face 1 inch in diameter.   Rs. 1650/- each

Product Details:

Cement Autoclave AS PER IS-4031    Rs. 49000/-
For Conducting accelerated soundness test of cement complete with all accessories inner chamber made of S.S. fitted with automatic pressure control switch
The Autoclave is suitable for conducting accelerated soundness tests on cements of the autoclave expansion test requiring constant steam pressure with the correspondent constant pressure. It consists of a stainless steel cylinder with a welded heat insulated flange, mounted on a sturdy supporting frame, enclosed in a heat insulated metal housing, attractively finished. The attached control unit encloses a sensitive pressure regulator and pressure gauge, power switches and pilot lights for controlling the electric heating units. Inside Chamber Dimensions-10.5 diameter x40.5cm height suitable for operation on 230V,50Hz, Single Phase, A.C. Supply. Supplied complete with test bar holder, special rack to hold specimens above water level in the autoclave and in a vertical position to expose them in the same manner..

OPTIONAL AT EXTRA COST:-

Digital Temp.Indicator  EXTRA    Rs.5000/-

Digital Pressure State Extra        Rs. 12000/-

Additional Information:

• Delivery Time: 4-6 Days
• Packaging Details: Wooden Packing

Product Details:

Flakiness gauge as per I.S.2386 Part I. Constructed in thick M.S.Sheet with different slots as per specifications. Used to determine the flakiness index of the aggregate. The aggregate particles are to be considered flaky, if their thickness is less than 0.6 of their nominal size. It consists of a frame with sliding panel with accurate slots of different standard width and length, the complete assembly is chrome plated or powder coated. Rs. 300/-